Since most of the questions in Elance Cisco Test are the same as those in Odesk Cisco Test, I need not repeat myself because even the syllabus is the same. To prepare for this exam, click Odesk Cisco Test Link, published earlier.
Free Elance Cisco Test Questions and Answers
Question 1
What should be the value of
configuration register in a router to boot IOS image stored in ROM?
a. 0x2102
b. 0x2101
c. 0x2142
d. ox101
Question 2
Which of the following
routing protocols are distance vector routing protocols?
a. OSPF
b. RIP
c. EIGRP
d. IGRP
Question 3
You executed the following
command on your router.
Router(config)#router ospf 15
Which command will you execute
next to complete OSPF configuration on your router?
a. Router(config-router)#
network 172.16.0.0. 255.555.0.0. area 5
b. Router(config)# network
172.16.0.0 0.0.255.255 area 5
c. Router(config-router)#
network 172.16.0.0. 0.0.255.255 area 5
d. Router(config# ip route
ospf 172.16.0.0 255.255.0.0 area 5
Question 4
If you have a subnet mask of
/26 for class c network, how many subnets and host per subnet will you get?
a. 4 network and 62 hosts
b. 16 networks and 16 hosts
c. 2 networks and 128 hosts
d. 62 networks and 2 hosts
e. 6 networks and 30 hosts
Question 5
Which of the following
devices can be connected using a Rollover cable?
a. Router Ethernet Port to
Router Ethernet Port
b. Switch Console Port to PC COM
Port
c. Switch Ethernet Port to
Switch Port
d. Router Ethernet Port to
Switch Ethernet Port
e. Router Console Port to PC COM
Port
Question 6
Which one of the following
addresses can be used as a host address for the subnet 192.168.50.16/28
a. 192.168.50.32
b. 192.168.50.16
c. 192.168.40.64
d. 192.168.50.30
Question 7
Which is the command to
configure q933a as frame relay LMI type?
a. Router(config)# frame-relay
lmi-type q933a
b. Router#lmi-type q933a
c.. Router(config-if)#frame-relay
lmi-type q933a
d. Router(config-if)#lmi-type
q933a
Question 8
If UDP receive datagrams that
are not in sequence, what will it do?
a. It will drop datagrams that
are not in sequence
b. It will arrange then in
sequence using sequence numbers
c. It will request source host
to resend them
d. None of the above
Question 9
Which of the following is a
valid unicast IP address?
a. 127.0.0.1
b. 224.5.7.1
c. 255.255.255.255
d. 172.16.5.15/30
e. 200.100.10.5/30
Question 10
What is the maximum number of
valid IP addresses in a class B network?
a. 165536
b. 65534
c. 256
d. 254
Question 11
Which
of the following provides routing protocol support for IPX. Appletalk and IP
networks
simultaneously?
a. RIPv2
b. OSPF
c. IGRP
d. EIGRP
Question 12
On which layer of the OSI
model do TCP & UDP work?
a. Transport layer
b. Session layer
c. Presentation Layer
d. Network Layer
Question 13
What is the command to show
Frame relay map table?
a.Router(config)# show frame-relay map
b. Router#show frame-relay
c. Router(config-router)#show
frame-relay table
d. Router#show frame-relay map
Question 14
Which of the following
commands show Cisco IOS image file name?
a. Show startup
b. Show running
c. Show version
d. Show history
Question 15
Which protocol is used to
find the MAC address of a device whose IP address is known?
a. ARP
b. SMTP
c. IARP
d. RARP
Question 16
Which command will you
execute to use 16 subnets of a class C network with subnet mask of 255.255.255.240?
a.Router(config)#ip all-subnets
b.Router(config)#ip subnet 16
c.Router(config)#ip classless
d.Router(config)#ip subnet-zero
Question 17
Which of the following
command is used to set console password?
a.Router(config)# enable secret
abc
b.Router(config)# enable
password abc
c.Router(config)# console
password abc
d. Router(config-line)#password
abc
Question 18
Which of the following VLANs
is recommended by Cisco to be used as an administrative VLAN?
a. VLAN 0
b. VLAN 1
c. VLAN 1024
d. VLAN 16
Question 19
What is the correct order of
data encapsulation in OSI model?
a.Packet, segment, frame, data,
bit
b. Segment, packet, frame, bit,
data
c. Bit, frame, segment, packet,
data
d. Data, segment, packet, frame,
bit
Question 20
Which of the following
statements are true for inter VLAN communication?
a. A router that supports inter
VLAN communication is required
b. The router must support the
same encapsulation method as supported by the switch
c. If the router has only one
Ethernet interface, sub-interfaces must be configured
d. All of the above
Question 21
Which statement is true about
RID(Router ID) in OSPF?
a. It is always the highest IP
address of active interfaces
b. It is the highest IP address
of all configured loopback interfaces
c. It is locally significant
d. It is only used for election
of DR
Question 22
Which command will you
execute to see whether the cable attached with your router’s Serial 0 is DCE or
DTE?
a. Show controllers serial 0
b. Show interface serial 0
c. Show IP interface serial 0
d.Show interface brief serial 0
Question 23
Which of the following
switching methods forward the frame after reading the destination MAC address
only?
a.Fast forward
b.Cut-through
c. Fragment free
d. Store and forward
Question 24
Which of the following
frame-tagging methods can be used for creating a trunk link between Cisco and
Non Cisco switches?
a. ISL
b. VTP
c. IEEE802.1Q
d. IEFT
Question 25
Which of the following are store in RAM?
a.Starup-config
b. Running-config
c. Routing table
d. All of the above
Question 26
Which two statement are true
about CHAP authentication method?
a. It is more secure than PAP
b. It is supported by HDLC
c. It is less secure than PAP
d. It sends authentication
messages periodically during the connection
Question 27
Which command will you use to
view sending and receiving of RIP update packets that normally run at the
background?
a. Router(config-router)#debug
ip rip
b. Router# debug rip packets
c. Router#debug ip rip
d. Router(config)# show rip
packets
Question 28
Which is the c ommand to
delete the configuration stored in NVRAM?
a. Delete nvram
b. Erase startup
c. Delete startup
d. Erase nvram
Question 29
What is the speed of a T1
line?
a. 128 kbps
b. 144 kbps
c. 2.048 Mbps
d. 1.544 Mbps
Question 30
If you set bandwidth of 64
kbps on an interface, what will be it’s cost in OSPF?
a. 256
b. 1562
c. 1024
d. 2096
Question 31
Which of the following must
be configured on a switch to segment Broadcast Domain?
a. VTP
b. PVC
c. VLAN
d. FTP
e. TFTP
Question 32
In which of the following
modes does a switch not participate in VTP domain, but still forward VTP
advertisement by trunk links?
a. Server
b. Domain
c. Client
d. Transparent
Question 33
Which command will disable
CDP on a router?
a. No cdp run
b. Disable cdp
c. No cdp enable
d. No cdp router
Question 34
Which command is used to
disable domain lookup?
a. No ip domain-lookup
b. Disable domain-lookup
c. No domain-lookup
d. None of the above
Question 35
How many access control list
can be applied on an interface?
a. One access control list in
each direction for each protocol
b. Two access control lists in
each direction
c. Unlimited
d. Access control list connate
be applied on an interface
Question 36
What is the network ID of IP
address 172.16.40.0/20?
a. 172.16.16.0
b. 172.16.36.0
c.172.16.32.0
d.172.16.0.0
Question 37
Different routing protocols
use different methods to calculate the distance to a network. What is that
method called?
a. Administrative Distance
b.Metric
c.Routing Table
d.None of the above
Question 38
What is the binary value of
157?
a. 11000111
b.10111001
c. 11100011
d. 10011101
Question 39
Which of the following
services can be used to set up a database of MAC addresses that can be used for
dynamic addressing of VLANs?
a. Static VLAN
b. VMPS
c. STP
d. VTP
Question 40
What is the main purpose of
creating VLANs?
a. They create single collision
domain
b. They provide fast speed to
the LANs
c. They break up the broadcast
domain
d. None of the above