How To Pass Elance Cisco Test Free Questions and Answers

Since most of the questions in Elance Cisco Test are the same as those in Odesk Cisco Test, I need not repeat myself because even the syllabus is the same. To prepare for this exam, click Odesk Cisco Test Link,  published earlier.

Free Elance Cisco Test Questions and Answers 

Question 1

What should be the value of configuration register in a router to boot IOS image stored in ROM?

a. 0x2102

b. 0x2101

c. 0x2142

d. ox101

Question 2

Which of the following routing protocols are distance vector routing protocols?

a. OSPF

b. RIP

c. EIGRP

d. IGRP

Question 3

You executed the following command on your router.

      Router(config)#router ospf 15

Which command will you execute next to complete OSPF configuration on your router?

a. Router(config-router)# network 172.16.0.0. 255.555.0.0. area 5

b. Router(config)# network 172.16.0.0 0.0.255.255 area 5

c. Router(config-router)# network 172.16.0.0. 0.0.255.255 area 5

d. Router(config# ip route ospf 172.16.0.0 255.255.0.0 area 5

Question 4    

If you have a subnet mask of /26 for class c network, how many subnets and host per subnet will you get?

a. 4 network  and 62 hosts

b. 16 networks and 16 hosts

c. 2 networks and 128 hosts

d. 62 networks and 2 hosts

e. 6 networks and 30 hosts

Question 5

Which of the following devices can be connected using a Rollover cable?

a. Router Ethernet Port to Router Ethernet Port

b. Switch Console Port to PC COM Port

c. Switch Ethernet Port to Switch Port

d. Router Ethernet Port to Switch Ethernet Port

e. Router Console Port to PC COM Port

Question 6

Which one of the following addresses can be used as a host address for the subnet 192.168.50.16/28

a. 192.168.50.32

b. 192.168.50.16

c. 192.168.40.64

d. 192.168.50.30

 

Question 7

Which is the command to configure q933a as frame relay LMI type?

a. Router(config)# frame-relay lmi-type q933a

b. Router#lmi-type q933a

c.. Router(config-if)#frame-relay lmi-type q933a

d. Router(config-if)#lmi-type q933a

Question 8

If UDP receive datagrams that are not in sequence, what will it do?

a. It will drop datagrams that are not in sequence

b. It will arrange then in sequence using sequence numbers

c. It will request source host to resend them

d. None of the above

Question 9

Which of the following is a valid unicast IP address?

a. 127.0.0.1

b. 224.5.7.1

c. 255.255.255.255

d. 172.16.5.15/30

e. 200.100.10.5/30

Question 10

What is the maximum number of valid IP addresses in a class B network?

a. 165536

b. 65534

c. 256

d. 254

Question 11

Which of the following provides routing protocol support for IPX. Appletalk and IP

networks simultaneously?

a. RIPv2

b. OSPF

c. IGRP

d. EIGRP

Question 12

On which layer of the OSI model do TCP & UDP work?

a. Transport layer

b. Session layer

c. Presentation Layer

d. Network Layer

Question 13

What is the command to show Frame relay map table?

a.Router(config)# show frame-relay map

b. Router#show frame-relay

c. Router(config-router)#show frame-relay table

d. Router#show frame-relay map

Question 14

Which of the following commands show Cisco IOS image file name?

a. Show startup

b. Show running

c. Show version

d. Show history

Question 15

Which protocol is used to find the MAC address of a device whose IP address is known?

a. ARP

b. SMTP

c. IARP

d. RARP

Question 16

Which command will you execute to use 16 subnets of a class C network with subnet mask of 255.255.255.240?

a.Router(config)#ip all-subnets

b.Router(config)#ip subnet 16

c.Router(config)#ip classless

d.Router(config)#ip subnet-zero

Question 17

Which of the following command is used to set console password?

a.Router(config)# enable secret abc

b.Router(config)# enable password abc

c.Router(config)# console password abc

d. Router(config-line)#password abc

Question 18

Which of the following VLANs is recommended by Cisco to be used as an administrative VLAN?

a. VLAN 0

b. VLAN 1

c. VLAN 1024

d. VLAN 16

Question 19

What is the correct order of data encapsulation in OSI model?

a.Packet, segment, frame, data, bit

b. Segment, packet, frame, bit, data

c. Bit, frame, segment, packet, data

d. Data, segment, packet, frame, bit

Question 20

Which of the following statements are true for inter VLAN communication?

a. A router that supports inter VLAN communication is required

b. The router must support the same encapsulation method as supported by the switch

c. If the router has only one Ethernet interface, sub-interfaces must be configured

d. All of the above

Question 21

Which statement is true about RID(Router ID) in OSPF?

a. It is always the highest IP address of active interfaces

b. It is the highest IP address of all configured loopback interfaces

c. It is locally significant

d. It is only used for election of DR

Question 22

Which command will you execute to see whether the cable attached with your router’s Serial 0 is DCE or DTE?

a. Show controllers serial 0

b. Show interface serial 0

c. Show IP interface serial 0

d.Show interface brief serial 0

Question 23

Which of the following switching methods forward the frame after reading the destination MAC address only?

a.Fast forward

b.Cut-through

c. Fragment free

d. Store and forward

Question 24

Which of the following frame-tagging methods can be used for creating a trunk link between Cisco and Non Cisco switches?

a. ISL

b. VTP

c. IEEE802.1Q

d. IEFT

Question 25

Which of the following  are store in RAM?

a.Starup-config

b. Running-config

c. Routing table

d. All of the above

Question 26

Which two statement are true about CHAP authentication method?

a. It is more secure than PAP

b. It is supported by HDLC

c. It is less secure than PAP

d. It sends authentication messages periodically during the connection

Question 27

Which command will you use to view sending and receiving of RIP update packets that normally run at the background?

a. Router(config-router)#debug ip rip

b. Router# debug rip packets

c. Router#debug ip rip

d. Router(config)# show rip packets

Question 28

Which is the c ommand to delete the configuration stored in NVRAM?

a. Delete nvram

b. Erase startup

c. Delete startup

d. Erase nvram

Question 29

What is the speed of a T1 line?

a. 128 kbps

b. 144 kbps

c. 2.048 Mbps

d. 1.544 Mbps

Question 30

If you set bandwidth of 64 kbps on an interface, what will be it’s cost in OSPF?

a. 256

b. 1562

c. 1024

d. 2096

Question 31

Which of the following must be configured on a switch to segment Broadcast Domain?

a. VTP

b. PVC

c. VLAN

d. FTP

e. TFTP

Question 32

In which of the following modes does a switch not participate in VTP domain, but still forward VTP advertisement by trunk links?

a. Server

b. Domain

c. Client

d. Transparent

Question 33

Which command will disable CDP on a router?

a. No cdp run

b. Disable cdp

c. No cdp enable

d. No cdp router

Question 34

Which command is used to disable domain lookup?

a. No ip domain-lookup

b. Disable domain-lookup

c. No domain-lookup

d. None of the above

Question 35

How many access control list can be applied on an interface?

a. One access control list in each direction for each protocol

b. Two access control lists in each direction

c. Unlimited

d. Access control list connate be applied on an interface

Question 36

What is the network ID of IP address 172.16.40.0/20?

a. 172.16.16.0

b. 172.16.36.0

c.172.16.32.0

d.172.16.0.0

Question 37

Different routing protocols use different methods to calculate the distance to a network. What is that method called?

a. Administrative Distance

b.Metric

c.Routing Table

d.None of the above

Question 38

What is the binary value of 157?

a. 11000111

b.10111001

c. 11100011

d. 10011101

Question 39

Which of the following services can be used to set up a database of MAC addresses that can be used for dynamic addressing of VLANs?

a. Static VLAN

b. VMPS

c. STP

d. VTP

Question 40

What is the main purpose of creating VLANs?

a. They create single collision domain

b. They provide fast speed to the LANs

c. They break up the broadcast domain

d. None of the above